Your Plumbing Crash Course: Tips for Bathtub Installation
Your Plumbing Crash Course: Tips for Bathtub Installation
Blog Article
We've found the article about Tools You Need to Install a New Bathtub below on the web and felt it made good sense to relate it with you on this site.
Installing a tub isn't precisely brain surgery, but it does call for solid plumbing, woodworking, and sometimes, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old tub is readily available, the job can move immediately; if you have to open a wall surface to remove the old tub as well as position the new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to vacate the old tub and embeded in the new one. Make certain you have certified yourself for the job and also fit attempting it. Rather than working with a service provider to take over a halfway-completed job, it is better to take into consideration employing one prior to you start. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly help you set up a brand-new tub in your washroom if you have currently purchased a new tub as well as don't need to alter the plan of your previous water supply pipes.
Your tools as well as material list should consist of the following:
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is separate the water system. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The procedure of removing the existing taps can be rather troublesome due to the restricted accessibility that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the staying water that will come from the pipelines. Once the supply pipes have actually been eliminated, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing substance.
Before moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipes.
If you require to fit a monobloc, then you will need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in place between the tap and also the sink. Secure the tap in place with the supplier provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former type should be connected to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the tub in the required placement. The wooden boards are helpful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bath tub till the spirit level reads level.
To set up faucets, fit the bottom of the furthest flexible faucet connector to the appropriate supply pipe by making a compression join; after that do the exact same for the various other faucet.
Switch on the water system and also inspect all joints and also brand-new pipework for leakages and also tighten them if required. Load the bath tub and additionally check the overflow outlet and also the regular outlet for leakages.
Finally, take care of the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the tub must wait until the bath tub has actually been utilized at the very least when as this will certainly resolve it right into its final setting.
Planning for the Installment
First of all, the supporting framework supplied with the bath must be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final position.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture an inflexible seal, creating the water to penetrate the wall surface between the bathroom and the tiling, bring about issues with wetness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your fixtures and installations. They are offered in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water before sealing, to enable the motion experienced when the bathtub is in usage. The sealer can break relatively very early if you do not consider this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly available on the market. It is a good idea to fit the floor tiles using water-resistant or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been brought to that article on Installing A Bathtub from a friend on another domain. Liked our review? Please share it. Let somebody else locate it. Thanks a lot for your time. Visit us again soon.
Search no more; expert plumbers. Report this page